Electronics-international SR-8A Manual de usuario

OI 020481 and II 012881Electronics International Inc. ®Smart Engine Analyzer(SR-8A)Operating and Installation InstructionsS02109211/28/88Rev. C: 2/2/9

8adjustments and wait 3 to 5 seconds between adjustments. As you approach peak the exhaust gastemperature will rise much slower until it starts to de

9INSTALLATION INSTRUCTIONSII 012881Rev. A 2/10/92You should have no trouble installing the Smart Analyzer in your aircraft. The instrument, probes an

6. Before starting the installation make sure the unit will fit in the location you intend to install it withoutobstructing the operation of any cont

a) Swt. #1: Set this switch DOWN if you wish to scan 8 channels. Set this switch UP if you wish toscan only 6 cylinders.b) Swt. #2: If you have a 6-c

4. EGT Probe Installation:A single EGT probe should be installed in the exhaust stack of the leanest cylinder. Each engine has its owncharacteristic

All Other EnginesEquipped with a 5/8"-18 Oil Drain PlugRemove the 5/8" - 18 oil drain plug located on the bottom of the engine. Install E.I

Note 1: Any channel will accept any one of E.I.s probes.Note 2: For channels requiring Precision Connectors, you will remove the Slip-on Connectors

Double the wires.Double CrimpE) Place a male connector on the red wire and a female connector on the yellow wire. Double crimp theseconnectors. A go

15Tie off any excess cable under the instrument panel. Be sure these cables do not obstruct the freedom oftravel of any controls.12. Hook Up Connect

wrong Extension Cable. If the reading is decreasing, your may have reversed the connectors on the Exten-sion Cable leads (the yellow wire on the prob

Important Notice***** MUST READ *****If you think it is not important to read this manual, you're wrong! This manualcontains important installat

When measuring from one lead (either lead) of the probe to the probe sheath (metal tip), there should bean open (10k or greater).2. Another method

18SPECIFICATIONS and OPERATING FEATURESS02189212/18/92Model: SR-8Weight: 16 oz.Environmental: Meets TSO C43aPower Requirements: 7.5 to 30 Volts, 1

SR-8AWiring DiagramWD 02189212/18/921912345678Connects to:Extension Cable Harness.Note: Any channel will accept any one of E.I.'s probes.Note:

SR-8A Sample Wiring DiagramForSingle 6-Cylinder Engine AircraftWD 02189222/18/922012345678Connects to:Channel markedon ext. cable.Extension Cable Harn

Appendix AAdding a Channel to the SR-8AIf you have an unused channel and would like to add an extension cable to your instrument, perform thefollowing

Appendix BSR-8A Circular ConnectorsInstrument Connector, Front View7613151116101421Yel1Red2Yel3Yel4Yel5Yel6Yel7Yel8Yel2Red3Red5Red4Red6Red8Red7RedNote

ContentsWarranty ------------------------------------------------------------------------------ 2Operating Instructions: ---------------------

2Warranty1209921Electronics International Inc. warrants this instrument and system components to be free from defects inmaterials and workmanship for

SR-8OPERATING INSTRUCTIONSOI 020481Rev: A 2/10/92The Smart Analyzer is easy to operate. You can learn the basic operation of this unit in the first f

FeaturesOperating InstructionsA set of switches on the back of the Smart Analyzer allows the unit to be set up for a 4 or 6-cylinder engine,fuel-injec

Features5Operating Instructions1) Any EGT or TIT channel exceeds 1650F.2) Any CHT channel exceeds 500F.3) Any EGT or TIT channel drops below 1100

6Operating Instructions FeaturesAnalyzer has detected a problem but it will not stop its scan until it reaches the hottest analyzerchannel. (Note: In

7Temperature Limits. The Smart Analyzer will automatically diagnose your engine during takeoff. A redTemp Prob light will alert you if the Smart A